Sensors
Showing 25–40 of 40 results
-
Sensors
TCS3200 Color Recognition Sensor Module
- Operating Voltage: 3V-5V
- High-resolution conversion of light intensity to frequency.
- Chip pins all has drawn for standard 100.
- Put the needle (2.54 mm).
- Mil-convenient for bitmap board.
- Programmable color and full-scale output frequency.
- Communicate directly with a microcontroller.
- Low-profile surface mount package.
SKU: TFF7-001 -
Sensors
TSOP1738 – Infrared Sensor
- Photo detector and preamplifier in one package
- Internal filter for PCM frequency
- Improved shielding against electrical field disturbance
- TTL and CMOS compatibility
- Output active low
- Low power consumption
- High immunity against ambient light
- Continuous data transmission possible (up to 2400 bps)
- Suitable burst length ≥10 cycles/burst
SKU: TFF4-004 -
Electronic Components, Sensors
Vibration Sensor Module SW-420
- Using SW-420 normally closed type vibration sensor
- Comparator output, clean signal, good waveform, strong driving ability, >15mA
- Operating voltage 3.3V ~ 5V
- Output format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
- With bolt holes for easy installation
SKU: TFF2-003 -
Electronic Components, Sensors
DHT11 Temperature and Humidity Sensor Module
DHT11 is a low-cost digital sensor for sensing temperature and humidity. This sensor can be easily interfaced with any micro-controller such as Arduino, Raspberry Pi etc to measure humidity and temperature instantaneously.
SKU: TAF6-001 -
Electronic Components, Sensors
DS18B20 Water Proof Temperature Sensor Probe Good Quality
- A probe by new original installation import DS18B20 temperature sensor chip.
- Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof.
- Stainless steel tube encapsulation waterproof moistureproof prevent rust.
- Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use stability.
- Without the external components, the unique single bus;
SKU: S-6005 -
Sensors, Electronic Components
MAX30102 PULSE OXIMETER HEART-RATE SENSOR MODULE GY-MAX30102
Specifications and Features:
- Optical sensor: IR and red LED combined with a photodetector
- Measures absorbance of pulsing blood
- I2C interface plus INT pin
- 3.3V power supply complete pulse oximeter and heart rate sensor solution, simplifies design, integrated LEDs, photo sensor, and
- high-performance analog front
- Ultra low power operation increases battery life for wearable devices
- Advanced functionality improves measurement performance, high SNR provides robust motion artifact resilience integrated
- ambient, light cancellation high sample rate capability fast data output capability
- It is an integrated pulse oximetry and heart rate monitor sensor solution.
SKU: TBF5-006 -
-
Electronic Components, Sensors
Pulse Sensor – Heart Rate Sensor Amped
Features :
- A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required.
- The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything.
- Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting.
SKU: TBF5-005 -
-
Electronic Components, Sensors
RC522 13.56MHZ RFID Reader Writer Module
- Voltage: DC 3.3V (Do not use 5V supply)
- Operating Current:13-26mA
- Idle Current:10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Typical operating distance in reading/Write mode is up to 50 mm
SKU: TAF4-005 -
Electronic Components, Sensors
TTP223 Touch Sensor Module(Pack of 5)
- Input Voltage : 2 Volt – 5.5 Volts DC.
- The response time max ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance(0~50pF).
- Stable touching detection of the human body for replacing traditional direct switch key.
- Provides direct mode toggle mode by pad option(TOG pin).
- After power-on have about 0.5sec stable-time, during the time do not touch the keypad, and the function is disabled.
- Auto calibration and Re-calibration period is about 4.0 sec when the key has not be touched.
SKU: TBF4-006