Shop
Showing 49–72 of 245 results
-
Relays
8 Channel Relay Module Isolated Optocoupler 5V 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Channel: 8 channel
- Relay Operating Voltage: 5V
- Power supply and relay instructions, lit, disconnect is off;
- Input signal, signal, common Terminal and start conducting;
- Input signal, signal, common Terminal and start conducting;
- Useful for appliance control;
- DC or AC signal, control, you can control the 220V AC load;
- There is a normally open and one normally close contact;
- The module is compliant with international safety standards, control and load areas isolation trenches.
* Product Images are shown for illustrative purposes
SKU: TDF6-004 -
Electronic Components
9v Battery Snap Connector + DC Jack(Battery Connector Cap)
- Excellent Material.
- Fine workmanship.
- It is an environmental 9V battery buckle.
- T- fonts, with red and black connecting lines.
- Save power and protect the environment.
- Good electrical conductivity and comfortable sense of touch.
SKU: TFF5-004-1 -
Electronic Components, Voltage Regulator ICs
9V Voltage Regulator IC | L7809CV
- Fixed output voltage is 9V
- Output current is 0.5A
- Dropout voltage is 2V
- Maximum DC input voltage is 35V
- Output transition SOA protection
- Output voltage tolerance is 4%
- Operating temperature range 0°C to 125°C
SKU: TBF7-004-2 -
Electronic Components, Sensors
ACS712 20A Current Sensor Module Good Quality
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
SKU: TBF2-003 -
-
Sensors
ADXL335 Module 3-axis Analog Output Accelerometer
- FPV, RC, and Robots systems
- GPS navigation systems
- Impact recognition and logging
- Gaming and virtual reality input devices
- Motion-activated functions
- Intelligent power saving for handheld devices
- Vibration monitoring and compensation
- Free-fall detection
- 6D-orientation detection
SKU: TBF9-004 -
Sensors
ADXL345 Tripple Axis Accelerometer Board
- Supply Voltage: 3.3 V/ 5V.
- Interface Type: I²C, SPI.
- Sensing Range: ±2g, ±4g, ±8g, ±16g.
- Sensitivity:
- X: 28.6 LSB/g.
- Y: 31.2 LSB/g.
- Z: 34.5 LSB/g.
- Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V.
- Free-Fall Detection.
- Tap/Double Tap Detection.
SKU: TBF9-002 -
-
Electronic Components, Microcontroller Boards
Ai-Thinker VC-02-Kit | Best Offline Voice Recognition Board
Electronic Components, Microcontroller BoardsAi-Thinker VC-02-Kit | Best Offline Voice Recognition Board
Features:
- All GPIOs can be configured as external interrupt input and wake-up source
- One full-duplex UART with the maximum rate of 3Mbps
- Support I2C，DAC，PWM and multiple interfaces
- Built-in 242KB high-speed SRAM
- Built-in 2MB FLASH
- Support dual-channel DAC output
- 32bit RISC core, running at 240MHz
- Support DSP instruction set and FPU floating point operation unit
SKU: TDF1-004 -
-
Microcontroller Boards
Arduino Mega 2560 R3 Board Good Quality Clone CH340G Board
- Microcontroller CH340
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- Dimensions : 111 x 54 x 12 (LxWxH) mm.
SKU: TBF6-004 -
Sensors
BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V.
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C).
- Peak current: 1.12mA.
- Operating Pressure: 300 hPa to 1100 hPa.
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.
SKU: TBF4-004 -
Cables
Cable for Arduino UNO/MEGA (USB A to B)-1M
- Fully compatible with the PC.
- Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions.
- Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
SKU: TDF10-003 -
