MQ3 Alcohol Sensor Module
- Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off).
- Current Consumption: 150mA.
- DO output: 0.1 and 5V.
- AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detecting Concentration: 0.05-10mg/L Alcohol.
₹93.22 ₹101.69
MQ3 Alcohol Sensor Module
Description
MQ3 Alcohol Sensor Module is made using Alcohol Gas Sensor MQ3. It is a low-cost semiconductor sensor which can detect the presence of alcohol gases at concentrations from 0.05 mg/L to 10 mg/L. The sensitive material used for this sensor is SnO2, whose conductivity is lower in clean air. Its conductivity increases as the concentration of alcohol gases increases. It has high sensitivity to alcohol and has a good resistance to disturbances due to smoke, vapor, and gasoline. This module provides both digital and analog outputs. MQ3 alcohol sensor module can be easily interfaced with Microcontrollers, Arduino Boards, Raspberry Pi etc.
This alcohol sensor is suitable for detecting alcohol concentration on your breath, just like your common Breathalyzer. It has a high sensitivity and fast response time. Sensor provides an analog resistive output based on alcohol concentration.
Features: MQ3 Alcohol Sensor Module
- 5V operation
- LEDs for output and power
- Output sensitivity adjustable
- Analog output 0V to 5V
- Digital output 0V or 5V
- Low Cost
- Fast Response
- Stable and Long Life
- Good Sensitivity to Alcohol Gas
- Both Digital and Analog Outputs
Specifications: MQ3 Alcohol Sensor Module
- Concentration: 0.05 mg/L ~ 10 mg/L Alcohol
- Operating Voltage: 5V ±0.1
- Current Consumption: 150mA
- Operation Temperature: -10°C ~ 70°C
* Product Images are shown for illustrative purposes only and may differ from actual product.
| Weight | 0.007 kg |
|---|---|
| HSN Code | 90319000 |
Based on 0 reviews
Be the first to review “MQ3 Alcohol Sensor Module”
You must be logged in to post a review.
Related products
-
Electronic Components, Sensors
DS18B20 Water Proof Temperature Sensor Probe Good Quality
- A probe by new original installation import DS18B20 temperature sensor chip.
- Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof.
- Stainless steel tube encapsulation waterproof moistureproof prevent rust.
- Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use stability.
- Without the external components, the unique single bus;
SKU: S-6005 -
Sensors
BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V.
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C).
- Peak current: 1.12mA.
- Operating Pressure: 300 hPa to 1100 hPa.
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.
SKU: TBF4-004 -
Electronic Components, Sensors
RC522 13.56MHZ RFID Reader Writer Module
- Voltage: DC 3.3V (Do not use 5V supply)
- Operating Current:13-26mA
- Idle Current:10-13mA
- Operating Frequency: 13.56MHz
- Highly integrated analog circuitry to demodulate and decode responses
- Supports ISO/IEC 14443 A/MIFARE
- Typical operating distance in reading/Write mode is up to 50 mm
SKU: TAF4-005
There are no reviews yet.