Search results: “arduino”
Showing 1–24 of 78 results
-
Sensors
Speed Measuring Sensor Module For Arduino
- Using imported groove optical coupling sensor, width 5mm.
- It has the output state light, if output high level, the lights are off. if output low level, it on.
- If it covered, it will output high level; otherwise, its output low level.
- Good signal and waveform, with a strong driving ability for more than 15mA.
- Equipped with a fixed bolt hole, easy install.
- Use the LM393 wide voltage comparer.
SKU: TBF9-004-1 -
Sensors
37 IN 1 Sensors Kit for Arduino
- For beginners who are interested in Arduino
- A complete set of Arduino’s most common and useful electronic components
- Infrared sensor receiving module
- Laser sensor module
- Temperature and humidity sensor module
- Infrared sensor module
- 5v relay module
- Obstacle avoidance sensor module.
SKU: THF1-001 -
Electronic Components
EP24 Thermal Printer With Case 5V-9V compatible with ESP32/Arduino
- Low-noise direct thermal printing method
- Fast printing speed, low noise
- Can support Max.40MM (diameter) paper roll, around 16-20 meter. Optional serial interface (RS-232C, TTL) / USB port
- Rich of graphics / curves / characters print function
- Easy paper loading structure
- Support 5V-9V wide power voltage
SKU: TDF7-005 -
-
-
Microcontroller Boards
Arduino Mega 2560 R3 Board Good Quality Clone CH340G Board
- Microcontroller CH340
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- Dimensions : 111 x 54 x 12 (LxWxH) mm.
SKU: TBF6-004 -
Sensors, Electronic Components
MQ 135 Air Quality/Gas Detector Sensor Module For Arduino
- Sensitivity to Ammonia, Sulphide, and Benzene steam
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Output voltage boosts along with the concentration of the measured gases increases.
SKU: TBF3-006 -
Electronic Components, Microcontroller Boards
Arduino Nano V3.0 Development Board – Clone Compatible Model (Unsoldered)
Electronic Components, Microcontroller BoardsArduino Nano V3.0 Development Board – Clone Compatible Model (Unsoldered)
- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: TBF6-005 -
-
Microcontroller Boards
Arduino Uno R3 SMD Atmega328P Board – Clone Compatible Model
- Microcontroller ATmega328 (SMD) – Interface CH340G
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 5-20V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
SKU: TAF3-003 -
Electronic Components, Motors & Motor Drivers
L293D Motor Driver Shield for Arduino
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, and internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: TDF6-002 -
Electronic Components, Miscellaneous components
4×4 Matrix Membrane Type Keypad Switch for Arduino, ARM and other MCU -16 Keys
Electronic Components, Miscellaneous components4×4 Matrix Membrane Type Keypad Switch for Arduino, ARM and other MCU -16 Keys
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
- Sticker can peel off for adhesive mounting.
- Operating Voltage (V): 12 DC
SKU: TBF5-007 -
Electronic Components, Sensors
BMP180 Barometric Pressure Sensor Module compatible with Arduino
- 1.8V to 3.6V Supply Voltage
- Low power consumption – 0.5uA at 1Hz
- I2C interface
- Max I2C Speed: 3.5Mhz
- Very low noise – up to 0.02hPa (17cm)
- Fully calibrated
- Pressure Range: 300hPa to 1100hPa (+9000m to -500m)
SKU: TBF4-003 -
-
-
-
Electronic Components, Relays
1 Channel 5V Relay Module with Optocoupler
- 1 channel relay board
- Operating Voltage 5V
- Max Current : 20mA
- Relay Contact Current Capacity at AC250V: 10A
- Relay Contact Current Capacity at DC5V: 10A
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
SKU: TFF1-002
